Mrslm.comMrslm.comMrslm.com
0
0$0.00
-22%

PWM Stepper Motor Driver Simple Controller Speed Controller Forward and Reverse Control Pulse Generation

$39.55 $30.99

Out of stock
Feature: 

Product name: simple controller
Model: CW-S01
It can generate PWM signal. There is a jumper on the board, which can be set and selected. By default, it is set to generate pulse frequency signal.
Product Manual:

1. When the controller generates a pulse frequency signal, it can supply a stepper driver as a signal. To control the stepper motor, it must be equipped with a driver.
(This simple controller + stepper driver + stepper motor + DC power supply can form a simple control platform.)
2. The controller can generate a pulse frequency signal or a PWM pulse width signal. There is a jumper on the board, which can be set and selected. By default, they are set to generate pulse frequency signals.
REQ is to generate pulse frequency signal
PWM is to generate PWM signal
3. When the controller generates a pulse frequency signal, there are three types of high, medium and low frequency signals that can be selected with a jumper. The frequency parameters are approximately:
High: 5.8KHZ-127KHZ
Middle: 590HZ-15.8KHZ
Low: 82HZ-2.3KHZ,
Frequency measurement: You can measure PUL and common cathode (GND) two ports.
4. The power supply has 2 sets of power input, and 2 sets only need to connect one set of power supply. It is recommended to use a power supply of more than 15V. Connect to the power supply of the 2-bit terminal, do not connect the positive and negative.
One group is the power supply connected to DC 15-160VDC, and the recommended operating voltage is 15-80VDC.
The other group is 5-12VDC. When used with the driver, it is recommended to use a minimum of 12V, not a 5V power supply, not at 5V, the power supply is connected to "5-12V input", and the power supply is connected to the "common cathode".
5. Length * width * height: about 73 * 51 * 37MM

Controller

Driver

PUL

Pulse negative terminal (PUL-)

DIR

Negative direction (DIR-)

ENA

Enable negative terminal (EN-)

Common anode

Common port (COM or + 5V or PUL + DIR + EN + are connected at the same time)

Common cathode

Common ground (GND)

5-12V input+

The positive end of the 12V power supply is generally empty.It is recommended to use a power supply of more than 15V.


 Example: Wiring with the common anode of the driver. If it is driven by 6 signal lines, the + 5V common terminals of the three signals must be connected in parallel to form a line and all connected to the common anode terminal.

 Package includes:

 1 x Controller

 Note:

1. If you want to use the start or stop function, the ENA enable terminal on the controller must be connected to the driver with a common cathode or a common anode.
2. The forward and reverse rotation and the start and stop of the motor can be controlled by pressing the button.
3. The speed of the motor can be controlled by adjusting the potentiometer to change the frequency.
4. The switch of the motor's forward / reverse rotation and start / stop is an ordinary switch with self-locking.
5. If you want to connect the switches that control forward and reverse, and open or stop, to the chassis panel, you can refer to the following instructions.
 Change the forward and reverse, the start-stop button into a lead-wire switch, see the pin position on the back:

1. When the common cathode is connected, the 1 and 3 pins are processed, and the 2, 4, 5, and 6 pins are empty
2. When the common anode is connected, the 1 and 2 pins are processed, and the 3, 4, 5, and 6 pins are empty
The two switches are the same pin lead.



(1) FREE Shipping 10 - 15 business days, (2) Standard Shipping 7 - 12 business days.

Shipping and Delivery Estimates

We ship in-stock orders as soon as possible. This is often within two business days, but there are situations where it may take longer. All estimates are based on business days.

Note:

(1) The shipping time mentioned above refers to the estimated time of business days that the shipment will take after an order has been shipped.

(2) Business days do not include Saturday/Sunday and any public holidays.

(3) These estimates are based on normal circumstances and are not a guarantee of delivery times.

(4) We are not responsible for the failures or delays in delivery resulting from any force majeure event, such as natural disaster, bad weather, war, customs issues, and any other event beyond our direct control.

Our policy lasts 14 days. If 14 days have gone by since your purchase, unfortunately we can't offer you a refund or exchange. To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.

for more information please visit our Refunds & Returns Policy page.

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Add to WishlistBrowse WishlistRemove Wishlist
Shopping cart
Free Shipping for all orders over [money]
Almost there, add [money] more to get FREE SHIPPING!
Congratulations! You've got free shipping!

Your cart is empty.

Return To Shop

Add Order NoteEdit Order Note
Add A Coupon

Add A Coupon

Coupon code will work on checkout page

PWM Stepper Motor Driver Simple Controller Speed Controller Forward and Reverse Control Pulse Generation

$39.55 $30.99
website